電氣自動化論文編號:ZD1089    論文字?jǐn)?shù):23072,頁數:62

目 錄
摘 要 Ⅱ
Abstract Ⅲ
目 錄 Ⅳ
1  緒論 1
 1.1  電子稱重技術的現狀 1
 1.2  電子稱重技術的發展趨勢 1
 1.3  項目研究背景 3
 1.4  本文的主要工作 4
2  系統方案論證與選型 5
2.1  控制器部分 5
2.2  數據采集部分 6
     2.1.1  傳感器的選擇 6
     2.2.2  放大電路選擇 9
 2.2.3  鍵盤處理部分方案論證 13 
2.3  顯示電路部分的選擇 13
2.4  超量程報警部分選擇 13
2.5  通訊接口部分方案論證 13
3  系統硬件電路設計 15
3.1  STC12C5A16S2的最小系統電路 15
 3.1.1  STC12C5A16S2單片機介紹 15
 3.1.2  單片機管腳說明 17
 3.1.3  STC12C5A16S2的最小系統構成 19
3.2  數據采集部分電路設計 19
       3.2.1  傳感器和其放大電路與STC12C5A16S2單片機接口電路設計 19
   3.2.2  測量算法 20
3.3  鍵盤輸入電路與STC12C5A16S2單片機接口電路設計 21
3.4  LED顯示電路與STC12C5A16S2單片機接口電路設計 22
 3.4.1  LED顯示器結構與原理 22
 3.4.2  LED顯示器與顯示方式 22
3.5  變平器與STC12C5A16S2單片機接口電路設計 23
 3.5.1  RS-232C機械連接器及引腳定義 23
 3.5.2  RS-232電平轉換芯片及電路 24
4  系統軟件設計 26
4.1  系統主程序 26
4.2  鍵盤管理模塊 27
4.3  數據處理模塊 29
4.4  計價模塊 29
4.5  上位機通訊 30
  4.5.1  MSComm控件的使用 30
  4.5.2  通訊過程 31
5  系統調試與分析 32
5.1  調試系統簡介 32
5.2  調試故障及原因分析 32
6  結  論 32
6.1  主要工作成果 33
6.2  存在的不足 34
致  謝 35
參考文獻 36
附錄 37

摘  要
 
 現代社會的發展，對稱重系統提出了更高的要求。目前，臺式電子秤在商業貿易中的使用已相當普遍，但存在一定的局限性，雖然在體積，成本控制方面有所改進，但需要工頻交流電源供應、攜帶不便、應用場所受到制約，且隨著信息技術的發展，某些領域人們需要對所得數據進行處理，期待測量更準確、價格更低廉且具有與PC機相連功能的電子秤投放市場。
 本文設計的電子秤以STC單片機為主要部件 ，用C語言進行軟件設計，硬件則以全橋傳感器FAB-80 為主，量程為0~10kg，隨時可改變上限閾值，并達到閾值報警的功能。在文中論述了稱重系統的工作原理，給出了系統電路設計與軟件流程，進行實物制作并調試。
   本文設計的基于單片機的電子稱重系統主要由電源、稱重傳感器、單片機、鍵盤/開關、LED顯示器,串口通信等構成智能稱重系統電路板，從而實現自動稱重系統的各種控制功能。可以說,此設計所完成的電子秤很大程度上滿足了應用需求。
關鍵詞: 串口通信; 稱重傳感器;STC 單片機; LED顯示器；FAB-80
  The development of the modern society has put forward higher request on weighing   technology. The desk-top electronic scales have been great application in commercial trade, but they have many shortcomings such as large volume, high cost, AC supplypower and not covenience to carry, so they are restricted to use. And with the development of information technology, some areas that people need to process the data So they have been expecting cheap portable electronic scales which can measure accurately and nd has the function of PC-linked electronic scale on the market.
 This electronic scale designed to take STC microcontroller as the main components, with using C language to Compile software in the thesis. And the hardware is based by full-bridge sensors FAB-80, its range is 0 ~ 10 Kilogram. Limited threshold value can be changed at any time to reach the alarm threshold function. The thesis discusses the working principle of weighing system, giving circuit design and software process and making physical production with debugging. 
 The microcontroller-based electronic weighing system consists of power supply, load cell, microcontroller, keyboard / switch, LED display, serial communications. All of them constitue an intelligent weighing systems board to achieve a variety of control functions of automatic weighing system. It can be said that the completion of the design of electronic scale meets the application requirements to a large extent.
  
Keywords: serial communication; load cell; STC microcontroller; LED display; FAB-80