車輛工程專業畢業論文，論文編號:JX942  論文字?jǐn)?shù):6110.頁數:31

摘  要
 本課題從實際生產中的一些冶金重載齒輪齒面發生嚴重塑性變形中得到啟發，認為必然存在最適合齒輪接觸強度和彎曲強度的齒形。經縝密分析和深入研究，初步認為這是等共軛曲率高階接觸的齒形，并分析了這種齒形的形成原理。本文通過對二階曲線和四階曲線的比較分析，并結合契貝謝夫多項式進行計算，分析高階接觸齒形的接觸應力,導出了計算公式。說明在高階接觸情況下有兩個應力極值點，并導出了極值點位置和接觸應力極值的公式。最后對一對共軛曲率的嚙合齒廓作了具體接觸應力計算。
 
關鍵詞：齒輪   應力   高階接觸

Abstract
 Inspired from some gears with heavy power transmission in practical usage after serious plastic deformation in metallurgical industry, we believe that there must existed some kind of gear profile which is most suitable in both the contact and bending fatigue strength. From careful analysis and deep going investigation, we think that it is the profile of equal conjugate curvature with high order of contact, and analyzed the forming principle of this kind of profile.Based on the second curve and comparative analysis of fourth order curves, combined with Chebyshev polynomial terms of higher order contact with tooth contact stress,formula derived.Note high exposure in the case of two extreme point of stress and extreme positions and the derived extreme contact stress formula.Finally, a pair of conjugate gear tooth profile curvature provides specific contact stress calculation.
Key word:  gear  stress  contact of high-level
目 錄
中文摘要 i
英文摘要 ii
目錄 iii
第一章  緒論 1
1.1  概述 1
1.2  國內外的情況 2
第二章  高階齒面嚙合間隙分析 4
第三章  契貝謝夫多項式計算 6
3.1 契貝謝夫正交多項式定義 6
3.2 用契貝謝夫多項式求接觸應力 6
3.3 相接觸曲面用契貝謝夫多項式展開 7
3.4  壓力分布用契貝謝夫多項式表示 8
3.5 總壓力 9
3.6 與赫茲接觸應力的對照 9
3.7 高階接觸 10
3.8 壓力分布用契貝謝夫多項 11
3.9 選取材料進行初步 13
第四章  VB程序繪制二階與四階曲  14
第五章  二階與四階曲線系數關系及應力分布 18
第六章  相似法畫齒形及其接觸齒面應力分析 22
     6.1 用相似法在范成儀上畫出齒輪 22
     6.2 接觸齒面應力 22
參考文獻 25
致謝 26
附件1  一對嚙合齒廓的坐標圖 27